
Digital PDM MEMS Microphone (66 dB A-weighted SNR)
JSM3526DB26GBP5
Digital PDM MEMS Microphone (66 dB A-weighted SNR)3.50×2.65×0.98mm · Bottom-port
A bottom-ported digital PDM silicon microphone: a MEMS sensor plus encoder IC converts the analog output to a 1-bit PDM stream — removing AC coupling, reducing RF noise coupling and easing PCB layout. Normal mode delivers 66 dB(A) SNR (20 Hz–20 kHz, A-weighted) with a 120 dB SPL acoustic overload point, a high-performance replacement for electret (ECM) microphones. The applied clock selects power-down / sleep / low-power / normal, down to 42 µA in sleep.
- SNR (20–20 kHz)
- 66 dB(A)
- AOP
- 120 dB SPL
- Sensitivity
- -26 dBFS
- Sleep current
- 42 µA
Key Features
Six capabilities built for the voice chainWhy JSM3526DB26GBP5
66 dB(A) high SNR
66 dB(A) A-weighted SNR over 20 Hz–20 kHz in normal mode: a lower noise floor and more algorithm headroom for NR and beamforming.
Four clock-selected states
Power-down / sleep / low-power / normal selected purely by clock frequency, no registers: 42 µA sleep, 300 µA low-power, ≤900 µA normal.
Direct PDM, no coupling caps
1-bit PDM output removes AC coupling caps, cuts RF noise pickup and is plug-and-play with mainstream audio codecs and SoCs.
120 dB SPL headroom
AOP 120 dB SPL at 10% THD with 0.15% typical THD — clean output even at high sound pressure.
Array-ready SELECT
The SELECT pin assigns L/R on a shared clock; two mics markedly improve far-field speech capture.
Cost-effective ECM replacement
Standard SMD reflow and pick-and-place, tape-and-reel — built for high-volume, cost-sensitive production.
Datasheet · Typical
Full SpecificationsSpecifications
Acoustic (Normal Mode)
Acoustic · Normal| SNR (20 Hz–20 kHz, A-wt.) | 66 dB(A) |
|---|---|
| SNR (low-power, 20 Hz–8 kHz) | 65 dB(A) |
| Sensitivity (typ -26) | -27 / -26 / -25 dBFS |
| AOP | 120 dB SPL |
| THD | 0.15 % |
| PSR / PSRR | -86 dBFS(A) / 65 dBFS |
| DC output offset | ±1 %FS |
Electrical & Power
Electrical & Power| Operating voltage VDD | 1.6 – 3.6 V |
|---|---|
| Normal current / clock | ≤900 µA @1–4.8 MHz |
| Low-power / clock | 300 µA @350–800 kHz |
| Sleep / clock | 42 µA @<250 kHz |
| Duty / rise-fall / jitter | 40–60% / 15 ns / 0.5 ns |
| Output load | ≤140 pF |
| Abs max supply | 6.5 V |
Mechanical & Ordering
Mechanical| Package | 3.50 × 2.65 × 0.98 mm |
|---|---|
| Pins | 5 (DATA/SELECT/GND/CLOCK/VDD) |
| Acoustic port | Ø0.325 ±0.05 mm (bottom port) |
| Directivity | Omnidirectional |
| Packing | Tape & reel · 5,000/reel (13") |
| Peak reflow | 260 ℃ (up to 5 cycles) |
Typical values at 25 C in the reference circuit; series production follows the official datasheet.
Pin Configuration
Pin DefinitionsPin Definitions
| Pin | Name | Description |
|---|---|---|
| 1 | DATA | PDM data out |
| 2 | SELECT | L/R channel select (internally pulled low; do not float) |
| 3 | GND | Ground |
| 4 | CLOCK | Clock input |
| 5 | VDD | Supply 1.6–3.6 V |
The SELECT pin is internally pulled low but must not float; ground all GND pins; avoid Class 2 dielectrics near the mic; use the same date code within one array module.
Applications
Typical Applications & PairingWhere It Fits
Ordering & Packaging
Ordering & PackagingHow to Buy
- Packaging
- Tape & Reel5,000 pcs/reel (13")
- Sample Policy
- Free Sample PackRequest via inquiry
- Lead Time
- Samples: 3 daysProduction: 8–12 weeks
Related Parts
Related Parts on the Same PlatformYou May Also Evaluate
Put this part into your next device
FAE support covers cavity review, reference circuits and dual-mic array references - reply within one business day.
Request Samples & Reference Design
Juchip Semiconductor
